home >> general construction >> job board >> post





[Concrete Finisher] *** Concrete Finishers, Form Carpenters and Foreman NEEDED -- Charlotte, NC (Local candidates ideal) -- Hourly/ OT ***

[ Back ] [ The Roadtechs General Construction Job Board ] [ Help ] [Edit ] [Mark Position Closed ]

Posted by: Tech USA LLC <wwinrow@techusa.net> on July 07, 2019 at 00:04:01. Click here to reply to this post via Email.Click here for help with email link

Post Number: 526496
Posted By: Tech USA LLC
Posted On: 2019-07-07 00:04:01
Email Address: wwinrow@techusa.net
Subject: [Concrete Finisher] *** Concrete Finishers, Form Carpenters and Foreman NEEDED -- Charlotte, NC (Local candidates ideal) -- Hourly/ OT ***
Contract / Temp to Direct / Direct Hire: Direct Hire


Set the forms that hold concrete to the desired pitch and depth, and align them.

Position construction forms or molds.


Check the forms that hold the concrete to see that they are properly constructed.

Inspect completed work to ensure proper installation.


Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.

Spread concrete or other aggregate mixtures.
Finish concrete surfaces.


Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.

Monitor construction operations.


Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.

Direct construction or extraction personnel.


Produce rough concrete surface, using broom.

Finish concrete surfaces.


Mold expansion joints and edges, using edging tools, jointers, and straightedge.

Finish concrete surfaces.


Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.

Clean surfaces in preparation for work activities.


Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.

Pour materials into or on designated areas.
Signal equipment operators to indicate proper equipment positioning.


Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.

Finish concrete surfaces.
Apply sealants or other protective coatings.


Operate power vibrator to compact concrete.

Compact materials to create level bases.


Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.

Smooth surfaces with abrasive materials or tools.


Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.

Drill holes in construction materials.
Position structural components.
Break up rock, asphalt, or concrete.


Waterproof or restore concrete surfaces, using appropriate compounds.

Apply sealants or other protective coatings.


Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.

Cut metal components for installation.
Apply decorative masonry finishes.


Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.

Finish concrete surfaces.


Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.

Prepare surfaces for finishing.
Install masonry materials.
Apply material to fill gaps in surfaces.


Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.

Finish concrete surfaces.
Install metal structural components.
Install building fixtures.


Fabricate concrete beams, columns, and panels.

Install masonry materials.
Fabricate parts or components.


Push roller over surface to embed chips in surface.

Apply decorative masonry finishes.


Build wooden molds, and clamp molds around area to be repaired, using hand tools.

Position construction forms or molds.
Build construction forms or molds.


Polish surface, using polishing or surfacing machine.

Smooth surfaces with abrasive materials or tools.


Apply muriatic acid to clean surface, and rinse with water.

Clean surfaces in preparation for work activities.


Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.

Apply decorative masonry finishes.


Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.

Mix substances or compounds needed for work activities.


Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.

Spread concrete or other aggregate mixtures.
Install roofing materials.



Thinking about applying for this position?
Please make sure that you meet the minimum requirements indicated for the job before you apply (see user agreement). If you are qualified, then use either the email link (near top of post) or the application link (near bottom of post) to apply, whichever is provided.


[ Back ] [ The Roadtechs General Construction Job Board ] [ Help ] [Edit ] [Mark Position Closed ]


61 page view(s)

© Copyright - Roadtechs®, LLC. All rights reserved. No reproduction of any part of this website may be sold or
distributed for commercial gain nor shall it be modified or incorporated in any other work, publication, or website.
Use of this site implies compliance with the Roadtechs User Agreement.