home >> nuclear >> job board >> post

[Design Engineer] Instrument and Controls Design Engineer onsite or remote!!

[ Back ] [ The Roadtechs Nuclear Job Board ] [ Help ] [Edit ] [Mark Position Closed ]


Job Title: Instrumentation and Controls (I&C) Design Engineer
Location: Remote or Greenville SC
Pay rate: $89.00 an hour
Travel: Could be travel depending on your location
Per Diem if traveling will be included

Job Description
The purpose of this position is to provide essential technical knowledge and perform engineering work as described below. This position serves as a staff engineer performing engineering assignment of intermediate complexity.
 Under direct supervision of the Discipline Lead Engineer or Area Lead Engineer, analyze and make independent recommendations regarding technical solutions to problems of intermediate complexity in accordance with project requirements
 Develop and review specifications and design criteria
 Perform and check engineering analyses and calculations; specify materials, equipment and systems; and solve technical problems of intermediate complexity
 Coordinate technical issues with other disciplines, project management, vendors and clients
 Execute work in compliance with Project Quality Plan and procedures
 Execute work in accordance with the approved project scope, cost and schedule baselines
 Establish, control and report on material key quantities; provide analysis and forecasts
 Provide technical support to activities associated with equipment and material procurement and subcontracting including scopes of work, technical bid evaluations and review of vendor submittals
 Provide technical support to activities associated with construction administration including response to construction requests-for-information and field changes
 Other duties as assigned

Basic Job Requirements
 U.S. Citizenship required
 Bachelor of Science degree in Control Systems Engineering, Electrical Engineering,
Chemical Engineering or related engineering field and minimum five (5) years of work related experience
 Working knowledge of applicable federal (including Department of Energy orders), state, and local codes and standards
 Ability to communicate effectively with audiences that include but are not limited to project management, coworkers, clients, vendors, and subcontractors
 Job related technical knowledge necessary to complete the job
 Intermediate knowledge of discipline codes and standards
 Ability to perform work in compliance with applicable local, state, and federal codes, statutes and guidelines
 Ability to attend to detail and work in a time-conscious and time-effective manner
 Intermediate computer and software skills to include proficiency in the use of word
processing, e-mail, spreadsheet and electronic presentation programs
 Experience providing engineering, procurement and construction (EPC) services on
commercial or industrial projects
 Proficiency executing EPC projects utilizing engineering analysis, 3D modeling and 2D
computer-aided drafting and design (CADD) automation tools in a multi-discipline
environment

Discipline Specific Job Requirements
 Perform a broad range of I&C design activities, including design definition, control systems architecture and development, digital systems, PLC, DCS, network configuration, logic development, network switches, process controls, P&ID development support and review, HMI, communication protocols, routing, and layout, SIL, and procurement activities
 Prepare and modify instrument and control systems design documents (e.g., instrument
datasheets, Input/Output wiring diagrams, schematics, panel layouts, logic diagrams, cable schedules, and instrument installation details)
 Perform control systems sizing calculations for control valves, relief valves, flow elements, thermowells and other instrumentation
 Create instrument index and datasheets and generate reports in Intergraph SmartPlant
Instrumentation database
 Develop intermediate complexity control systems narrative specifications
 Develop basic control systems logic diagrams and/or cause and effect diagrams
 Represent control systems and participate in model reviews
 Develop specifications and design of Distributed Control Systems (DCS), Programmable
Logic
 Controller (PLC) and Safety Instrumented Systems (SIS) hardware and software
applications; monitor DCS/PLC/SIS design developed by the design group

Preferred Qualifications
 Professional Engineer license
 Practical field experience
 EPC project experience for the following industries:
 U.S Department of Energy or other U.S. Federal Government Agency
 Nuclear facilities under a nuclear quality assurance program
 Manufacturing, pharmaceutical or biotechnology
 Proficiency with Bentley MicroStation
 Proficiency with Autodesk AutoCAD
 Proficiency with Intergraph SmartPlant Instrumentation (SPI)

Intermediate knowledge of:
 Specifying instrumentation
 Control systems procurement activities
 Piping and Instrumentation Diagram (P&ID) representation; can recognize/report
problems associated with control systems representation on P&ID
 Developing control strategies and represent on P&ID
 Instrument design and installation requirements


[ Back ] [ The Roadtechs Nuclear Job Board ] [ Help ] [Edit ] [Mark Position Closed ]


© Copyright - Roadtechs®, LLC. - All rights reserved.
Use of the Roadtechs.com website implies compliance with the Roadtechs User Agreement and acknowledgment of our Privacy Policy.