[ Back ] [ The Roadtechs Shipyard / Marine Job Board ] [ Help ] [Edit ] [Mark Position Closed ]
Shipfitter Loft Journeyperson
(6 months temp-to-hire opportunity)
- be DBIDS Eligible
- have Loftsperson experience or Lofting Vocational Training
- have 2015 AUTOCAT experience
This position is responsible for performing, with minimal supervision, tasks associated with designing and creating workstation drawings for the fabrication of components and assemblies that are used for alterations and repairs on Navy Ships, Military Sealift Command, and commercial projects. The position requires a comprehensive understanding of ship terminology, blueprint reading, measurements, and the ability to interpret job specifications and drawings. The qualifications and general capabilities listed below are representative of the knowledge, skill, and ability desired by the shipyard.
EDUCATION AND EXPERIENCE
1. High school degree or equivalent (GED), or completion of vocational training (certificate) in a related field.
2. Six (6) years of related experience, three (3) of which were in the maritime environment.
3. Must have held the position of loftsperson within the last three (3) years or completed lofting vocational training.
4. Must have some experience repairing and installing structural plates and shapes, and foundations on ships.
QUALIFICATIONS, DUTIES, AND RESPONSIBILITIES
1. Accomplish ship checks as required.
2. Have a comprehensive understanding of ship repair terminology and ship compartment location nomenclature.
3. Understand the operation of fabricating machines such as shears, brakes, presses, forming rolls and routers.
4. Ability to read and interpret structural drawings, sketches, and specifications.
5. Ability to interpret appropriate sections of NAVSEA, ABS, Coast Guard standards and manufacturer’s tech manuals.
6. Ability to comprehend instructions, drawings, and general correspondence.
7. Ability to add, subtract, multiply, and divide whole numbers, fractions, and decimals. Must understand the US customary and metric measurement systems.
8. Understand the principle of balancing air systems including taking proper readings and documenting the results.
9. Ability to write comprehensive Condition Found Reports (CFR) describing the material condition of the ship as it pertains to the assigned work item, and provide recommended corrective action.
10. Ability to effectively confer job related information to the structural supervisor, improvers, and helpers.
11. Must be physically and medically capable of wearing all required personal protective equipment (PPE) required for the job as prescribed under OSHA standards. PPE includes hard hat, safety glasses, steel toe shoes, goggles, respirator, safety harness, safety line, flotation gear, etc.)
12. Comply with OSHA standards and BAE best safety practices.
13. Arrive at the designated work site at the assigned time and end the shift as directed by the schedule and your supervisor.
14. Work shifts and overtime as assigned.
15. Keeping the work area clean and safe at all times, especially at the end of the shift.
16. Complete daily work assignments and provide status of unfinished work for shift turnover.
17. Provide quality work and Objective Quality Evidence (OQE) as required by the work specifications or assigned by the supervisor.
18. Comply with the Company’s “Non-Discrimination and Anti-Harassment Policy” which expects that all relationships among persons in the workplace will be businesslike and free of bias, prejudice, and harassment.
19. Carry out written and verbal instructions.
20. Resolve unexpected events related to your assigned task in a professional manner.
The working environment in the shipyard varies from a normal office conditions to working outside where precipitation, wind, extreme cold, and extreme heat and high humidity are not unusual. When working inside of vessels the environment may be smoky, hot or cold, and have low levels of illumination may be present.
There are heavy equipment and power tools operating almost at every location. Depending on the type of work available, reasonable accommodation may be made to enable individuals with disabilities to perform the job requirements.
Personnel can expect to work in a variety of spaces from confined areas accessible only by manholes to high platforms accessible only by scaffolding or ladders. Work may also be accomplished using mechanical lifts as working platforms.
The noise level in the shipyard environment is usually loud, especially inside of vessels. The noise encountered in the shop is generally low to moderate. The wearing of appropriate personal protective equipment is mandatory.
There is always the potential of falling objects and personnel are occasionally exposed to moving mechanical parts during work. Appropriate PPE must always be worn.
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of the job. Must be able to tour all vessels, piers, docks and work sites.
While performing the duties of this job, the employee is regularly required to: stand; walk; use hands to finger, handle or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch or crawl; and talk or hear.
The employee is occasionally required to sit.
SPECIFIC PHYSICAL REQUIREMENTS: May be required to demonstrate any or all requirements.
1. Lift/push/pull 50 lbs to 100 lbs on an occasional basis (0-33% of the day).
2. Lift/push/pull up to 20 lbs on a frequent basis (34-66% of the day).
3. Perform prolonged standing (2-3 hours). Bend, squat crouch, crawl and kneel. 4. Climb in a safe manner (climbing, includes stairs, scaffolding, ladders and ramps).
5. Work at a variety of levels and positions (ex. Waist, eye, above head).
6. Good balance while working on uneven surfaces and maneuvering obstacles.
7. Sufficient handgrip and coordination to carry and operate tools and equipment.
8. Access work areas through 18” x 36” openings and work in confined spaces for prolonged periods of time (33-66% of the day).
9. Respond to visual, verbal, and audible sounds/commands.
10. Work at heights above 12’ from ladders, scaffolding, and manlifts.
11. Fully extend the arm while reaching overhead, reaching out, reaching to the side and reaching down.
12. Perceive attributes of an object/material such as size, shape, temperature and texture by means of receptors in the hands and fingers.
13. Turn head from side to side and about on the vertical axis. Turn body at the waist from side to side and about the vertical axis.